Free cookie consent management tool by TermsFeed Update cookies preferences

How to choose current transformer for your application

For a 10kV incoming panel of an 800 kVA transformer, the designer specified a CT ratio of 200/5, intending to select a higher primary rating as a conservative safety margin. However, this design failed utility revenue metering approval. The normal operating current is only 46 A, which is merely 23% of the CT primary rated current. For standard metering CTs, accuracy error degrades sharply below 20% of rated primary current, resulting in persistent under-registration of energy.

This real-world pitfall highlights why current transformer selection is far more than simply picking a rough oversize margin. Many panel builders and system integrators run into metering rejection, billing disputes or protection malfunctions by misunderstanding CT class, ratio, duty and winding requirements.

In this guide, we break down the core rules to properly select metering, measurement and protection CTs for your power distribution projects.

Basic Requirements for current transformer selection

Depending on their intended application, current transformers (CTs) are primarily categorized into three types: CT for measurement, CT for revenue metering, and CT for protection. Since the applications differ, the selection requirements for these CTs also vary. The selection criteria for each of the three types are outlined below. 

Selection of Current Transformers for Measurement Purposes
Accuracy ClassRated Primary CurrentRated secondary currentSecondary load
No lower than Class 0.5 For special purposes: Class 0.2S, 0.5SThe rated primary current should be close to, but not less than, the maximum normal load current of the primary circuit. For analog (pointer-type) instruments, the rated primary current should preferably be no less than 1.25 times the maximum load current of the circuit.1A、5ABased on whether the instrument transformers are installed within the switchgear or at a centralized location, calculate the length of the connecting cables between the transformers and the measuring instruments to determine the secondary burden; a value of ≤10 VA may be adopted.
Selection of Current Transformers for Metering
Accuracy ClassRated Primary CurrentRated secondary currentRated Output Capacity
Class III and IV electric energy metering installations shall be equipped with current transformers of an accuracy class no lower than 0.5S.The rated primary current should be selected such that the actual load current in the circuit during normal operation reaches 60% of the rated value; it should not be less than 30% of the rated value, or 20% for S-class [current transformers].1A, 5A1. When connected to a static electricity meter, the capacity should preferably not exceed 10 VA.
Selection of Current Transformers for Protection Purposes
Accuracy ClassAccuracy limit factor currentSecondary Burden
5P, 10P5, 10, 15, 20, etc.Based on whether the instrument transformers are installed within the switchgear or at a centralized location, calculate the length of the connecting cables between the transformers and the protection devices to determine the secondary burden; a value of ≤10 VA may be adopted.
Selection of Current Transformers for Protection Purposes
Accuracy ClassAccuracy limit factor currentSecondary Burden
5P, 10P5, 10, 15, 20, etc.Based on whether the instrument transformers are installed within the switchgear or at a centralized location, calculate the length of the connecting cables between the transformers and the protection devices to determine the secondary burden; a value of ≤10 VA may be adopted.

How to choose current transformer for your application

CT Rated Voltage & CT Construction Type

The CT rated insulation voltage must match the system voltage. For a 10kV switchgear application, we select a 10kV class CT with insulation rated for the highest system operating voltage Um = 12kV.

There are two mainstream construction types for medium-voltage CTs.

The first is Post-type (Resin cast). It has a separate primary winding and needs thermal and dynamic stability verification. This type is most widely used inside switchgear cabinets.

The second is Busbar type, also known as Window or Through-core type. The busbar or cable running through the CT serves directly as the primary conductor. It is suitable for bushing feed-through positions and circuits with extremely high short-circuit current.

Rated Primary Current (CT Ratio)

Select CT primary rating so that normal operating load sits around 60% of the CT primary rated current.

– Operating current >120% In: Overload, rising error and winding overheating

– Operating current <20% In (standard class): Large accuracy drift, metering error

– Revenue metering circuits: Target ~2/3 of rated primary current for best performance

For example: 800kVA, 10kV transformer, Nominal side current: I = 800 / (√3 × 10) ≈ 46 A

select 75/5 CT ratio: 46 / 75 = 61% Ideal range

Select 50/5 CT ratio: 46 / 50 = 92% Too close to overload limit

Select 200/5 CT ratio: 46 / 200 = 23% Light-load error risk.

Standard primary current values

5,10,15,20,30,40,50,75,100,150,200,300,400,500,600,750,800 A… always round up from calculated load.

Notes

Standard 0.2 / 0.5 class CTs only guarantee accuracy from 20% to 120% In.

S-class CT (0.2S / 0.5S)** extends the accuracy range down to 1% In. For projects with fluctuating loads and obvious light-load periods such as commercial buildings and residential complexes, S-class metering windings are strongly recommended.”

CT accuracy class

For Class I and Class II energy metering, 0.2S class CT is specified, used for grid revenue metering and high-consumption users. 0.5S class CT applies to Class III and lower metering for regular users. For general indication measurement that does not involve billing, Class 0.5 or Class 1 CT is acceptable. For standard overcurrent relay protection, 10P10 or 10P20 CT is adopted, which limits the error ≤10% at 10 times rated current. Critical protection circuits use 5P20 CT, guaranteeing error ≤5% at 20 times rated current.

In a word, metering windings must be independent and dedicated, never shared with measurement or protection windings, and metering windings have higher accuracy than measurement windings.

Secondary current and rated capacity

You can choose either 5A or 1A secondary current, as conductor loss rises with the square of current. 5A is the common choice for devices mounted inside the same cabinet with good meter compatibility. 1A is preferred for cable runs longer than roughly 30 m to remote panels, to cut wiring loss.

We need to verify the actual secondary burden, which equals the sum of instrument consumption and cable loss. The actual burden must stay between 25% and 100% of the CT rated VA, to keep the CT within its accuracy range. We calculate total burden based on cable length, cross-section and secondary current, then pick a suitable VA rating.

Example 1: Same-cabinet installation.

For a 10kV feeder cabinet with 5A secondary current, the microprocessor protection relay consumes 1 VA. The secondary cable is 2.5mm² with a one-way length of 8 m. The calculated cable resistance is 0.11 Ω, resulting in wiring loss of 2.8 VA. Total secondary burden S₂ = 1 + 2.8 = 3.8 VA. A 5P20 / 10 VA winding is selected, with valid working range [2.5, 10] VA. Since 3.8 VA falls within this range, this selection is acceptable.

Example 2: Long remote cable run for the same circuit, with cable length extended to 50 m.

If 5A secondary current is kept, total burden reaches 18.5 VA and exceeds the 10 VA rating, which is invalid. Switching to 1A while still using a 10 VA winding gives a total burden of 1.7 VA, below the 25% minimum burden limit, so it also fails. Finally, we adopt 1A secondary current with a 5 VA winding. Its valid range is [1.25, 5] VA. The total burden of 1.7 VA accounts for 34% of the rated value and meets the requirement.

Verification of CT Dynamic and Thermal Stability

Verifying the dynamic and thermal stability of a current transformer (CT) is the primary differentiator in the selection process for CTs versus potential transformers (PTs). Since short-circuit current flows directly through the CT’s primary winding, its dynamic and thermal stability must be verified. Dynamic stability verification requires the CT’s rated dynamic current idyn to be greater than or equal to the short-circuit impulse current ish = 2.55 × Ik. Thermal stability verification requiresIt² × t ≥ Ik² × tk, (Normalized to 1s: It(1s) ≥ Ik × √tk).

For example, consider a three-phase short-circuit current Ik = 20kA at the installation point—a typical level for a 10 kV busbar in a commercial or residential building—with a short-circuit duration of 0.6 seconds. Calculations indicate a required dynamic stability rating of ≥51kA and a 1-second thermal stability rating of ≥15.5kA.

These values ​​must be provided to the CT manufacturer to ensure they meet the rated dynamic current and 1-second rated short-time thermal current specifications found in the product catalog. This is the inherent limitation of CTs with low transformation ratios: a lower ratio implies more turns in the primary winding and thinner conductors, which significantly reduces the CT’s capacity to withstand short-circuit currents. A 150/5 CT and a 600/5 CT differ by orders of magnitude in terms of their dynamic and thermal stability capabilities.

If the verification fails, there are three potential solutions: increase the transformation ratio (using an ‘S-class’ CT to maintain accuracy under light-load conditions), select a reinforced-insulation model (indicated by a ‘Q’ suffix in the model number), or switch to a busbar-type CT. In a busbar-type CT, the busbar itself serves as the primary winding; therefore, dynamic and thermal stability are determined by the cross-section of the busbar, making them virtually unlimited.

Wiring, Polarity and Secondary Circuit

1. Wiring: For 10kV unearthed neutral systems, revenue metering commonly uses two CTs in V-connection (two-element three-phase three-wire). Protection wiring follows relay manufacturer requirements (two-phase or three-phase connection).

2. Polarity: P1 faces the source / busbar side, P2 faces the load. Incorrect polarity causes reverse energy registration or protection maloperation. Polarity test is mandatory during site commissioning.

3. Never open CT secondary circuit: An open secondary leads to extreme overvoltage, winding damage and safety hazards.

   – Do NOT install fuses on CT secondary

   – Short the secondary terminals with shorting blocks before disconnecting meters live

   – Short and earth unused windings

4. Single-point earthing CT secondary circuit must be earthed at one single location only. Multiple earth points create circulating current and corrupt metering & protection signals.

5. Do not mix residual CT: Zero-sequence / core-balance CTs for earth fault protection are separate devices, with completely different specification logic from phase CTs.

Conclusion

In summary, for standard metering and measurement applications within 10kV switchgear, epoxy-cast, dual-winding current transformers (CTs) with an accuracy class combination of 0.2S+0.5S are typically selected. For protection purposes within 10kV switchgear, CTs with classes such as 5P20 or 10P10 may be used; these are often designed as multi-winding units housed within a single enclosure, integrated alongside the metering windings.

In scenarios where high short-circuit currents coexist with a requirement for low current ratios—a challenging combination—busbar-type CTs are the preferred choice, as their dynamic and thermal stability are inherently ensured by the busbar itself. Busbar-type CTs are also well-suited for installation at wall-bushing locations, where they can simultaneously serve the function of a wall bushing. For outdoor installations or environments with heavy pollution, outdoor-rated cast-resin CTs should be used; in such cases, the creepage distance must be verified against the specific pollution level, while accuracy classes can be flexibly configured to meet project requirements.

Related Articles

News

How to use gas analyzer

Learn how to use a gas analyzer in five steps: preparation and calibration, sample introduction, measurement, data analysis, and shutdown. Overview of using gas analyzer

Read More »
News

What are contactor types

Want to know contactor types? This article will introduce different types of contactors. Contactor Types by Voltage of the Control Coil Contactors can be classified

Read More »